A and H Models  
   
 

  Home > Uhlenbrock DCC Digital > Decoders for rolling stock of all gauges > PluX Decoders >

The PluX interface has been developed to allow up to 9 separate operable functions to be controlled by a locomotive decoder.  Manufacturers and digital installers are now building in such functions as smoke generators, cab lighting , digital uncoupling, firebox glow, operating pantographes and PluX gives them the ability to combine a number of these in one model. Plux is an interchangable system that allows a PluX22 socket to accept decoders with PluX22, PluX16, PluX12 or PluX8 plugs to be installed depending on your needs.

Pin Number
 
1
GP10/C Hall Sensor in
2
Function Output AUX3
3
GP10/B Train bus clock line (or SUSI)
4
GP10/A Train bus data line (or SUSI)
5
GND Ground -ve
6
U+ (Alternate blue)
7
Headlight (White)
8
Motor 1 (Orange)
9
U+ (Blue)
10
Motor 2 (Grey)
11
Index - no pin
12
Track Pick Up Right (Red)
13
Taillight (Yellow)
14
Track Pick Up Left (Black)
15
Loud speaker A
16
Function Output AUX1
17
Loud speaker B
18
Function Output AUX2
19
Function Output AUX4
20
Function Output AUX5
21
Function Output AUX6
22
Function Output AUX7


ImageCodeNameDescriptionPriceQty 
 
UH33150Uhlenbrock 33150 Intellisound 3 Minidecoder PluX16

33150 Intellisound 3 Minidecoder PluX16

Due 2012 details to be confirmed

£80.91
 
UH36360Uhlenbrock 36360 Intellisound 3 Decoder PluX22

36360 Intellisound 3 Decoder PluX22

Supplied without speaker

£80.91
Uhlenbrock 71680 NEM658 PluX interface
UH71680Uhlenbrock 71680 NEM658 PluX interface

71680 NEM658 PluX interface adaptor board with solder points

£8.14
 
UH73140Uhlenbrock 73140 Decoder scale N-TT with PluX 12

73140 Decoder scale N-TT with PluX12 connector

DCC Multi-protocol decoder with load regulation for DC and Faulhaber motors.  With higher current capacity for small locos with High current demands (N, TT, OO/HO)

73140 Features
• Regulated Multi-protocol decoder for DCC, Motorola – with automatic system recognition for analog DC
• Suitable for DC and Bell armature motors up to 0.7A (1.5A peak current)
• Quiet motor running with 18.75KHz control frequency
• 14, 27, 28, 31 and 128 speed steps depending on the data format
• Short (1-127) and long (128-9999) addresses
• NMRA compatible
• Minimum, maximum and middle speeds adjustable
• Speed step table for 14, 28 and 31 speed steps
• Main line programming (DCC)
• Shunting speed (half speed) switched with F3
• Direction dependent, dimmable lighting switched via F0
• Two additional function outputs
• With solder pads for connecting Uhlenbrock IntelliSound modules or LISSY Mini transmitter
• Reacts to DCC brake signal (e.g. from Power 3) “Brake diode” or braking section in DC operation.
• All outputs have short circuit protection
• Conventional DC operation with automatic switching between DC and digital mode
• All CVs programmable by digital devices with DCC and Motorola formats
• Programmable via register, direct CV or page mode in DCC operation
• Updatable using Flash memory
Dimensions: 14.5 x 8.3 x 2.4mm
New 2011
£27.18
Uhlenbrock 76150 Intellidrive Deluxe PluX16
UH76150Uhlenbrock 76150 Intellidrive Deluxe PluX16

76150 Intellidrive Deluxe PluX16

Multi-protocol decoder with load control for locomotives with a 16-pole PluX interface

Characteristics
·          Regular multi-protocol decoder for DCC and Motorola
·          Suitable for DC and bell armature motors to 1 A
·          Quiet motor running through 18.75 KHz control frequency
·          14, 27, 28, 128 speed steps, depending upon data format
·          Short (1-127) and long (128-9999) Addresses
·          Conforms to NMRA
·          Minimum, maximum and mid speed adjustable
·          Main line programming (DCC)
·          Shunting mode (half speed) switchable with F3
·          Acceleration/Brake delays switchable with F4
·          Direction dependent lights, dimmable, switchable with F0
·          Light changing and 2 Special functions
·          With SUSI-interface for connecting Sound modules or other modules for controlling switchable auxiliary functions (f1-f12) via the PluX-interface
·          Produces the address identification controlling a LISSY mini transmitter module 68 400 via the PluX interface
·          Reacts to a DCC conforming brake signal or brake section with DC voltage
·          All Output have short circuit protection
·          Analogue DC or AC with automatic change over to the respective operating mode
·          All CVs can be programmed with digital devices using the DCC and Motorola formats
·          Programmable by register, direct CV or Page programming in the DCC operation
·          With output for Pickup switch 71 750
·          Updatable with Flash-Memory
£29.91
Uhlenbrock 76560 Intellidrive Deluxe PluX22
UH76560Uhlenbrock 76560 Intellidrive Deluxe PluX22

76560 Intellidrive Deluxe PluX22

Multi-protocol decoder with load control for locomotives with a 22-pole PluX interface

Characteristics
·          Regular multi-protocol decoder for DCC and Motorola
·          Suitable for DC and bell armature motors to 1 A
·          Quiet motor running through 18.75 KHz control frequency
·          14, 27, 28, 128 speed steps, depending upon data format
·          Short (1-127) and long (128-9999) Addresses
·          Conforms to NMRA
·          Minimum, maximum and mid speed adjustable
·          Main line programming (DCC)
·          Shunting mode (half speed) switchable with F3
·          Acceleration/Brake delays switchable with F4
·          Direction dependent lights, dimmable, switchable with F0
·          Light changing and 7 Special functions
·          Outputs may be set for temporary use ( eg. Automatic uncouplers) or flashing.
·          With SUSI-interface for connecting Sound modules or other modules for controlling switchable auxiliary functions (f1-f12) via the PluX-interface
·          Produces the address identification controlling a LISSY mini transmitter module 68 400 via the PluX interface
·          Reacts to a DCC conforming brake signal or brake section with DC voltage
·          All Output have short circuit protection
·          Analogue DC or AC with automatic change over to the respective operating mode
·          All CVs can be programmed with digital devices using the DCC and Motorola formats
·          Programmable by register, direct CV or Page programming in the DCC operation
·          With output for Pickup switch 71 750
·          Updatable with Flash-Memory
£36.27

« Back

 
 Return to main site View Cart